View PS9115_552886.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA SHEET
PHOTOCOUPLER
PS9115
HIGH CMR, 10 Mbps TOTEM POLE OUTPUT TYPE 5-PIN SOP PHOTOCOUPLER -NEPOC
Series-
DESCRIPTION
The PS9115 is an optically coupled high-speed, totem pole output isolator containing a GaAlAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. The PS9115 is specified high CMR, high CTR and pulse width distortion with operating temperature.
FEATURES
* High common mode transient immunity (CMH, CML = 20 kV/s TYP.) * Small package (5-pin SOP) * Pulse width distortion ( tPHL - tPLH = 7 ns TYP.) * High-speed (10 Mbps) * High isolation voltage (BV = 2 500 Vr.m.s.) * Totem pole output * Ordering number of taping product: PS9115-F3, F4: 2 500 pcs/reel * Pb-Free product * Safety standards * UL approved: File No. E72422 * DIN EN60747-5-2 (VDE0884 Part2) approved No. 40008902 (Option)
1 2 1. Anode 2. Cathode 3. GND 4. VO 5. VCC
PIN CONNECTION (Top View)
5 4 3
TRUTH TABLE APPLICATIONS
* Measurement equipment * PDP * Line Receiver for FA Network
ON OFF L H LED Output
The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version.
Not all devices/types available in every country. Please check with local NEC Compound Semiconductor Devices representative for availability and additional information.
Document No. PN10267EJ02V0DS (2nd edition) Date Published February 2005 CP(K) Printed in Japan
The mark
shows major revised points. (c) NEC Compound Semiconductor Devices, Ltd. 2003, 2005
PS9115
PACKAGE DIMENSIONS (UNIT: mm)
3.4 +0.3 -0.1
7.00.3 4.4
2.60.2
0.15 +0.10 -0.05
0.10.1
1.27 0.4 +0.10 -0.05 0.25 M
0.50.3
MARKING EXAMPLE
9115 N234
No. 1 pin Mark Initial of NEC (Engraved mark)
N
Assembly Lot *1
N
2 34
Week Assembled Year Assembled (Last 1 Digit) Rank Code
*1
Bar : Pb-Free
2
Data Sheet PN10267EJ02V0DS
PS9115
ORDERING INFORMATION
Part Number Order Number Solder Plating Specification PS9115 PS9115-F3 PS9115-F4 PS9115-V PS9115-V-F3 PS9115-V-F4 PS9115-A PS9115-F3-A PS9115-F4-A PS9115-V-A PS9115-V-F3-A PS9115-V-F4-A Magazine case 100 pcs Embossed Tape 2 500 pcs/reel DIN EN60747-5-2 (VDE0884 Part2) Approved (Option) Pb-Free
*2
Packing Style
Safety Standard Approval
Application Part Number PS9115
*1
Magazine case 100 pcs Embossed Tape 2 500 pcs/reel
Standard products (UL approved)
*1 For the application of the Safety Standard, following part number should be used. *2 With regards to terminal solder (the solder contains lead) plated products (conventionally plated), contact your nearby sales office.
ABSOLUTE MAXIMUM RATINGS (TA = 25C, unless otherwise specified)
Parameter Diode Forward Current
*1
Symbol IF VR VCC VO IOH IOL PC BV TA Tstg
Ratings 30 5 7 7 -5 13 130 2 500 -40 to +85 -55 to +125
Unit mA V V V mA mA mW Vr.m.s. C C
Reverse Voltage
Detector
Supply Voltage Output Voltage High Level Output Current Low Level Output Current Power Dissipation
*2
Isolation Voltage
*3
Operating Ambient Temperature Storage Temperature
*1 Reduced to 0.3 mA/C at TA = 25C or more. *2 TA = -40 to +85C, Applies to output pin VO and power supply pin VCC. Reduced to 2.36 mW/C at TA = 70C or more. *3 AC voltage for 1 minute at TA = 25C, RH = 60% between input and output. Pins 1-2 shorted together, 3-4 shorted together.
RECOMMENDED OPERATING CONDITIONS
Parameter High Level Input Current Low Level Input Voltage Supply Voltage TTL (loads) Operating Ambient Temperature Symbol IFH VFL VCC N TA 0 MIN. 7.5 0 4.5 5.0 TYP. MAX. 12.5 0.8 5.5 3 +85 C Unit mA V V
Data Sheet PN10267EJ02V0DS
3
PS9115
ELECTRICAL CHARACTERISTICS (TA = 0 to +85C, unless otherwise specified)
Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Detector High Level Output Current
*2
Symbol VF IR Ct IOH VOH VOL ICCH ICCL IOSH
Conditions IF = 10 mA, TA = 25C VR = 3 V, TA = 25C V = 0 V, f = 1 MHz, TA = 25C VCC = VO = 5.5 V, VF = 0.8 V VCC = 4.5 V, VF = 0.8 V, IOH = -2 mA VCC = 4.5 V, IF = 7 mA, IOL = 8 mA VCC = 5.5 V, IF = 0 mA, VO = open VCC = 5.5 V, IF = 10 mA, VO = open VCC = 5.5 V, VO = GND, IF = 0 mA, 10 ms or less
MIN. 1.4
TYP.
*1
MAX. 1.9 10
Unit V
1.65
A
pF
30 0.003 2.4 3.0 0.25 12 13 -26 0.6 16 16 200
A
V V mA mA mA
High Level Output Voltage Low Level Output Voltage High Level Supply Current Low Level Supply Current High Level Output Short Circuit Current Low Level Output Short Circuit Current Coupled Threshold Input Current (H L) Isolation Resistance
IOSL
VCC = VO = 5.5 V, IF = 8 mA, 10 ms or less
34
mA
IFHL
TA = 25C VCC = 5 V, VO = 0.6 V
2.3
5 6
mA
RI-O
VI-O = 1 kVDC, RH = 40 to 60%, TA = 25C
10
11
Isolation Capacitance Propagation Delay Time (H L)
*3
CI-O tPHL
V = 0 V, f = 1 MHz, TA = 25C TA = 25C VCC = 5 V, IF = 7.5 mA 15 10 15 10
0.6 33 65 85 40 65 85 7 50
pF ns
Propagation Delay Time (L H)
*3
tPLH
TA = 25C VCC = 5 V, IF = 7.5 mA
ns
Pulse Width Distortion (PWD)
*3
tPHL-tPLH
VCC = 5 V, IF = 7.5 mA
ns
Common Mode Transient Immunity at High Level Output
*4
CMH
VCC = 5 V, TA = 25C, IF = 0 mA, VO (MIN.) = 2 V, VCM = 1 kV
10
20
kV/s
Common Mode Transient Immunity at Low Level Output
*4
CML
VCC = 5 V, TA = 25C, IF = 7.5 mA, VO (MAX.) = 0.8 V, VCM = 1 kV
10
20
kV/s
4
Data Sheet PN10267EJ02V0DS
PS9115
*1 Typical values at TA = 25C *2 Because a high-level output current (IOH) of 300 A or more may be output when the temperature is 0C or less and when VCC is around 3 to 4 V, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. *3 Test circuit for propagation delay time
VCC = 5 V Pulse input (IF) VO (monitor) (PW = 500 ns, Duty cycle = 1/2) Input (monitor) 47 0.1 F 1.3 k VCC = 5 V IF (ON) 50% IF (ON)
Input
VOH
CL = 30 pF
Output
2.5 k
tPHL
tPLH
1.5 V VOL
CL includes probe and stray wiring capacitance.
*4 Test circuit for common mode transient immunity
SW IF VCC = 5 V 0.1 F VO (Monitor) CL = 15 pF
VCM
VCM 90% 10%
tr
tf
1 kV 0V
VO (IF = 0 mA) VO (IF = 7.5 mA)
VOH 2V 0.8 V VOL
CL includes probe and stray wiring capacitance.
USAGE CAUTIONS
1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 F is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity.
Data Sheet PN10267EJ02V0DS
5
PS9115
TYPICAL CHARACTERISTICS (TA = 25C, unless otherwise specified)
MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE
40
Detector Power Dissipation PC (mW) Maximum Forward Current IF (mA)
DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE
150
30
100
20
50
10
0
20
40
60
80 85
100
0
20
40
60
80 85
100
Ambient Temperature TA (C)
Ambient Temperature TA (C)
FORWARD CURRENT vs. FORWARD VOLTAGE
100
High Level Supply Current ICCH (mA) Low Level Supply Current ICCL (mA)
SUPPLY CURRENT vs. AMBIENT TEMPERATURE
20 VCC = 5.5 V 16 ICCL (IF = 10 mA) 12 ICCH (IF = 0 mA) 8
Forward Current IF (mA)
10 TA = +85C +50C +25C 0C -25C
1
0.1
4
0.01 1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
0 -50
-25
0
25
50
75
100
Forward Voltage VF (V)
Ambient Temperature TA (C)
HIGH LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE
Propagation Delay Time tPHL, tPLH (ns), Pulse Width Distortion tPHL - tPLH (ns)
PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE
50 IF = 7.5 mA VCC = 5.0 V 40 tPLH tPHL
5
High Level Output Voltage VOH (V)
4
VCC = 4.5 V, VF = 0.8 V, IOH = 2.0 mA
3 2
30 20
1
10 PWD 0 -50 -25 0 25 50 75 100
0 -50
-25
0
25
50
75
100
Ambient Temperature TA (C)
Ambient Temperature TA (C)
Remark The graphs indicate nominal characteristics.
6
Data Sheet PN10267EJ02V0DS
PS9115
LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE
0.5
Low Level Output Voltage VOL (V) Threshold Input Current IFHL (mA)
THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE
5 VCC = 5.0 V 4
0.4
VCC = 4.5 V, IF = 7.5 mA, IOL = 8.0 mA
0.3 0.2
3
2
0.1
1
0 -50
-25
0
25
50
75
100
0 -50
-25
0
25
50
75
100
Ambient Temperature TA (C)
Ambient Temperature TA (C)
LOW LEVEL OUTPUT VOLTAGE vs. LOW LEVEL OUTPUT CURRENT
0.5
High Level Output Voltage VOH (V) Low Level Output Voltage VOL (V)
HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT
5 TA = 85C 25C 0C 3 2 VCC = 4.5 V, VF = 0.8 V
VCC = 4.5 V, IF = 5.0 mA 0.4 TA = 85C 0C 25C
4
0.3 0.2
0.1
1
0
2.5
5
7.5
10
12.5 13
0
-1
-2
-3
-4
-5
Low Level Output Current IOL (mA)
High Level Output Current IOH (mA)
HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT
Propagation Delay Time tPHL, tPLH (ns), Pulse Width Distortion tPHL - tPLH (ns)
PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. FORWARD CURRENT
60 TA = 25C, VCC = 5 V tPHL
4
High Level Output Voltage VOH (V)
TA = 85C 25C 3 0C
VCC = 4.5 V, IF = 250 A
40
2
tPLH 20 PWD
1
0
-5
-10
-15
-20
-25
-30
-35
0
5
10
15
20
25
30
High Level Output Current IOH (mA)
Forward Current IF (mA)
Remark The graphs indicate nominal characteristics.
Data Sheet PN10267EJ02V0DS
7
PS9115
TAPING SPECIFICATIONS (UNIT: mm)
Outline and Dimensions (Tape)
2.00.05 4.00.1
1.750.1
7.40.1
1.5+0.1 -0
3.45 MAX.
1.550.1
8.00.1
12.00.2
5.50.1
3.90.1
3.00.1
0.30.05
Tape Direction
PS9115-F3
PS9115-F4
Outline and Dimensions (Reel)
2.00.5
2.00.5
13.00.2
R 1.0
21.00.8
13.00.2
3302.0
1001.0
13.51.0
17.51.0
Packing: 2 500 pcs/reel
11.9 to 15.4 Outer edge of flange
8
Data Sheet PN10267EJ02V0DS
PS9115
NOTES ON HANDLING 1. Recommended soldering conditions
(1) Infrared reflow soldering * Peak reflow temperature * Time of peak reflow temperature * Time of temperature higher than 220C * Time to preheat temperature from 120 to 180C * Number of reflows * Flux 260C or below (package surface temperature) 10 seconds or less 60 seconds or less 12030 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
Recommended Temperature Profile of Infrared Reflow
Package Surface Temperature T (C)
(heating) to 10 s
260C MAX. 220C
to 60 s
180C
120C
12030 s (preheating)
Time (s)
(2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260C or below (molten solder temperature) 10 seconds or less 120C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron * Peak Temperature (lead part temperature) * Time (each pins) * Flux 350C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100C
Data Sheet PN10267EJ02V0DS
9
PS9115
(4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
2. Cautions regarding noise
Be aware that when voltage is applied suddenly between the photocoupler's input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings.
USAGE CAUTIONS
1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity.
10
Data Sheet PN10267EJ02V0DS
PS9115
When the product(s) listed in this document is subject to any applicable import or export control laws and regulation of the authority having competent jurisdiction, such product(s) shall not be imported or exported without obtaining the import or export license.
* The information in this document is current as of February, 2005. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. * NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. * NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation, NEC Compound Semiconductor Devices, Ltd. and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above).
M8E 00. 4 - 0110
Data Sheet PN10267EJ02V0DS
11
PS9115
Caution
GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth.
For further information, please contact NEC Compound Semiconductor Devices, Ltd. http://www.ncsd.necel.com/ E-mail: salesinfo@ml.ncsd.necel.com (sales and general) techinfo@ml.ncsd.necel.com (technical) Sales Division TEL: +81-44-435-1588 FAX: +81-44-435-1579 NEC Compound Semiconductor Devices Hong Kong Limited E-mail: ncsd-hk@elhk.nec.com.hk (sales, technical and general) FAX: +852-3107-7309 TEL: +852-3107-7303 Hong Kong Head Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Taipei Branch Office FAX: +82-2-558-5209 TEL: +82-2-558-2120 Korea Branch Office NEC Electronics (Europe) GmbH http://www.ee.nec.de/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279
0406

▲Up To Search▲

Price & Availability of PS9115

	To Download PS9115 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .